Course Descriptions


여기를 클릭하면 PDF 파일로 만들어진 코스 설명을 보실 수 있습니다.

--

사용 언어를 선택하여 아래에 특정 언어로 코스를 보시거나 검색 바를 이용하여 특정 코스를 검색하실 수 있습니다.

English Español Français Italiano Português 简体中国



색인을 사용하여 용어집 보기

특집 | A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | 전체보기

페이지:  1  2  3  4  5  6  7  8  9  10  ...  14  (다음)
  전체보기

1

1500SJ Service Training

1500SJ Service Training covers the Ultra Boom Series 1500SJ straight boom lift. This class covers machine operational characteristics, hydraulic and electrical systems, canbus system, JLG analyzer, calibrations, and troubleshooting basic hydraulic and electrical systems.

Duration: Three days (24 hours)
Who Should Take This Class: Technicians who service and repair JLG 1500SJ boom lift machines
Prerequisite: Recommended - Ultra Boom Lift Service Training
Models Covered: 1500SJ

1500SJ维修培训

1500SJ维修培训涵盖超长悬臂系列1500SJ直臂升降机。该课程介绍设备工作特点、液压和电气系统、控制器局域网总线(canbus)系统、JLG分析仪、校准以及如何对基本液压和电气系统进行故障排查。

培训长度:三天(24小时)
本课程适用对象:JLG 1500SJ型悬臂升降机保养和维修技师
录取先决条件:建议-已完成超长悬臂升降机维修培训
针对型号:1500SJ

2

260MRT Scissor Lift Service Training

260MRT Scissor Lift Service Training covers the engine-powered 260MRT scissor lift. This class covers machine operational characteristics, hydraulic and electrical systems, canbus system, JLG analyzer, calibrations, and troubleshooting basic hydraulic and electrical systems.

Duration: One day (8 hours)
Who Should Take This Class: Technicians who service and repair JLG 260MRT scissor lift machines
Prerequisite: Recommended - Technician Fundamentals
Models Covered: 260MRT

260MRT剪叉式升降机维修培训

260MRT剪叉式升降机维修培训涵盖260MRT剪叉式升降机。该课程介绍设备工作特点、液压和电气系统、控制器局域网总线(canbus)系统、JLG分析仪、校准以及如何对基本液压和电气系统进行故障排查。

培训长度:一天(8小时)
本课程适用对象:JLG 260MRT剪叉式升降机保养和维修技师
录取先决条件:建议-具备技师基础知识
针对型号:260MRT

3

340AJ Service Training

340AJ Boom Lift Service Training covers the 340AJ articulated boom lift. This class covers machine operational characteristics, hydraulic and electrical systems, canbus system, JLG analyzer, calibrations, and troubleshooting basic hydraulic and electrical systems.

Duration: Two days (16 hours)
Who Should Take This Class: Technicians who service and repair JLG 340AJ boom lift machines
Prerequisite: Recommended - Technician Fundamentals
Models Covered: 340AJ

340AJ悬臂升降机维修培训

340AJ悬臂升降机维修培训涵盖340AJ曲臂式升降机。该课程介绍设备工作特点、液压和电气系统、控制器局域网总线(canbus)系统、JLG分析仪、校准以及如何对基本液压和电气系统进行故障排查。

培训长度:两天(16小时)
本课程适用对象:JLG 340AJ悬臂升降机保养和维修技师
录取先决条件:建议-具备技师基础知识
针对型号:340AJ

A

Aerial Work Platform (AWP) Operator Training

Not available at this time

Most countries require or recommend operators of Aerial Work Platforms (AWPs) or Mobile Elevated Work Platforms (MEWPs) to be trained before any operation. This class teaches operators to safely operate Aerial Work Platforms based on the requirements of the American National Standards Institute/Scaffold Industry Association (ANSI/SIA) standards and the International Organization for Standardization (ISO) standards.

Duration: One day (8 hours)
Who Should Take This Class: Everyone who operates any Aerial Work Platform
Prerequisite: None

B

base sugli impianti idraulici

Il corso base sugli impianti idraulici è un programma di e-learning composto da 10 moduli. Il corso tratta le teorie ed i principi base dell’idraulica, i simboli degli schemi idraulici ed il funzionamento base dei componenti idraulici. Al momento, questo corso è disponibile solo in inglese.

Durata: Autogestita, normalmente da 2 a 6 ore
A chi è destinato il corso: Tecnici che eseguono la riparazione e la manutenzione delle macchine JLG
Prerequisito: Nessuno
Modelli trattati: Nessuno

Basic Electricity Course

The Basic Electricity course is a seven-module e-learning program. The course covers basic electrical theory and principles, electrical schematic symbols, and the basic operation of electrical components. This course is only available in English at this time.

Duration: Self-paced, typically 2 to 6 hours
Who Should Take This Class: Technicians who service and repair JLG machines
Prerequisite: None
Models Covered: None

Basic Hydraulic Course

The Basic Hydraulics course is a ten-module e-learning program. The course covers basic hydraulic theories and principles, hydraulic schematic symbols, and the basic operation of hydraulic components. This course is only available in English at this time.

Duration: Self-paced, typically 2 to 6 hours
Who Should Take This Class: Technicians who service and repair JLG machines
Prerequisite: None
Models Covered: None


페이지:  1  2  3  4  5  6  7  8  9  10  ...  14  (다음)
  전체보기